LM3886 , 100W Power Audio Amplifier circuit

The following circuit diagram is the 100 Watt power audio amplifier circuit, build based on power amp chip LM3886. The single chip of IC LM3886 is able to amplify the audio power output up to 68W.

In this circuit, the two of LM3886 are paralled to gain more powerful amplifier output. This amplifier can deliver about 50W into a 8-ohm speaker and 100W into a 4-ohm speaker. To make a stereo amplifier, there are should be use 4 pieces of LM3886.

Circuit source: http://www.shine7.com/audio/pa100.htm

20W Bridge Car Amplifier based TDA7240A

The following circuit diagram is a bridge amplifier which specially designed for car audio system. The circuit is very simple with few external components supporting the power IC TDA7240A. This circuit will produce a maximum power output of 20W

Schematic Diagram:

PCB Layout:

The circuit diagram and PCB layout come from the IC TDA7240A datasheet. Download TDA7240A datasheet for circuit reference.

Positive Variable Power Supply circuit

The following diagram is the schematic diagram of positive adjustable/variable power supply. It means that the power supply output will be DC current with positive [+] and ground [0] polarity.

Schematic diagram:

Power Supply Input:

Component part list:
R1 = 330
R2 = 1K
VR1 = 10K 10-turn trimpot
C1 = 2200uF/50V
C2,4 = 100nF ceramic
C3,4 = 10uF/63V
D1-6 = 1N5403
REG IC = LM317T
Heatsink

Visit this page to download the variable power supply diagram manual.

32W HiFi Amplifier circuit based on TDA2050

This is a High Fidelify (Hi-Fi) amplifier circuit based on single IC TDA205. This is a mono channel audio amplifier. You need to build the same circuit for stereo channel.

Schematic diagram:

PCB Design:

TDA2050 Description:
The TDA 2050 is a monolithic integrated circuit in Pentawatt package, intended for use as an audio class AB audio amplifier. Thanks to its high power capability the TDA2050 is able to provide up to 35W true rms power into 4 ohm load @ THD =10%, VS = ±18V, f = 1KHz and up to 32W into 8ohm load @ THD = 10%, VS = ±22V, f = 1KHz. Moreover, the TDA 2050 delivers typically 50W music power into 4 ohm load over 1 sec at VS=22.5V, f = 1KHz.

The high power and very low harmonic and crossover distortion (THD = 0.05% typ, @ VS = ±22V, PO = 0.1 to 15W, RL=8ohm, f = 100Hz to 15KHz) make the device most suitable for both HiFi and high class TV sets.

Download TDA2050 datasheet for the circuit reference.

TDA7295, 80W Audio Amplifier

Below is a schematic diagram of the 80W power amplifier based on single Power IC TDA7295. With simple diagram, this circuit will be easy to build.

The IC TDA7295 is a monolithic integrated circuit , intended for use as audio class AB amplifier in Hi-Fi field applications such as home theatre and topclass TV.

Continue reading about this 80W audio amplifier.

Triangle Wave and Square Wave Generator

This is a simple circuit diagram of triangle wave and square wave generator.



The circuit is designed based on a common 1458 dual op-amp that can be used from very low frequencies to about 10 Khz. The time interval for one half cycle is about R*C and the outputs will supply about 10 milliamps of current. Triangle amplitude can be altered by adjusting the 47K resistor, and waveform offset can be removed by adding a capacitor in series with the output.

source of Triangle Wave and Square Wave Generator circuit:
http://www.high-voltage-lab.com/211/triangle-squarewave-generator

10W Audio Amplifier circuit based on TDA1910

Simple and cheap, that's the advantage of this circuit. Although the output power is not high but audio quality is good, because TDA1910 has a very low noise feature. This circuit suitable for use as a student project.

About TDA1910:
The TDA1910 is a monolithic integrated circuit in MULTIWATT® package, intended for use in Hi-Fi audio power applications, as high quality TV sets.

The TDA 1910 meets the DIN 45500 (d = 0.5%) guaranteed output power of 10W when used at 24V/4W. At 24V/8W the output power is 7W min.

TDA1910 Features:

• muting facility
• protection against chip over temperature
• very low noise
• high supply voltage rejection
• low “switch-on” noise.

Download TDA1910 Datasheet for complete TDA1910 reference

Simple FM Transmitter

This FM transmitter claimed to be a very good transmitter. This circuit is worked very well since this circuit is actually copied from available electronic kit.

Component part:

R1 100K R2 220K R3 22R R4 1K trimmer R5 1K R6 56K R7 1M R8 1K2 T1 BF244A or BF245A FET T2 2N3819 FET T3 BC307/8/9 or BC557/8/9 PNP

D1 Varicap diode (eg. BB119) D2 1N4148 C1 5pF ceramic C2 6pF ceramic C3 15pF ceramic C4 trimmer cap C5 15pF ceramic C6 1nF ceramic C7 100uF electrolytic C8 4.7uF electrolytic C9 100pF ceramic

Frequency range is 100-108 MHz. The circuit is only mono circuit, and accepts an audio input from either a microphone or other source. The input impedance is 1Mohm. The input sensitivity is 5mV and the max input signal is 10mV. The transmitted signal can be picked up on a FM radio. The circuit can be used for short-range transmission, eg. for wireless microphones.

The power supply to use is 9-14 V DC, one of the little rectangular 9V batteries is fine. Connect this to the + and - points on the PCB. The sound input goes to the points marked "MIKE". The antenna should be connected to the point marked "ANT". The emitter's output impedance is 50 ohms. You can make your own fancy antenna if you like.

Source: http://www.high-voltage-lab.com/77/small-radio-transmitter