High Quality Intercom circuit

This is an intercom circuit which use LM380 as the audio amplifier and 2 transistors as the microphone pre amplifier. The sound quality will be good enough with low cost building.

This circuit consists of two identical intercom units. Each unit contains a power supply, microphone preamplifier, audio amplifier and a Push To Talk (PTT) relay circuit. Only 2 wires are required to connect the units together. Due to the low output impedance of the mic preamp, screened cable is not necessary and ordinary 2 core speaker cable, or bell wire may be used.

Detail explanation about this intercom circuit include the PCB layout, please visit this page

Stereo Tone Control circuit

This is stereo tone control circuit based on IC LM1036. The circuit should be works with supply voltage 9V to 15V DC.

And here the circuit's features:

Wide supply voltage range, 9V to 16V
Large volume control range, 75 dB typical
Tone control, ±15 dB typical
Channel separation, 75 dB typical
Low distortion, 0.06% typical for an input level of 0.3 Vrms
High signal to noise, 80 dB typical for an input level of 0.3 Vrms

Infrared Toggle Switch schematic diagram

Use this Infrared toggle switch for wireless switching. You need to add IR receiver to electronic device for switching using this circuit.

COMPONENTS

R8________________ 680R
R7, R9____________ 4K7
R1, R2, R4, R6____ 27K
R3________________ 100K
R5________________ 1M
C1, C2, C5________ 470nF
C3, C4, C6________ 47u/16v ecap
IC________________ 4013
Q2, Q3____________ BC548
Q1________________ BC558
D1________________ 1N4148
D2________________ 1N4004
ZD1_______________ Zener diode 5V6
IR receiver module
LED
Miniature relay AZ-SH-112L

All modern IR remote control devices produce a continuous coded stream of pulses at 37.9 kHz when any button on the module is pressed. These IR pulses are detected and decoded by a receiver (your TV, VCR etc.) and the appropriate function activated. In our Kit the coded stream is converted into a single pulse and that single pulse is used to toggle a relay on & off. The coded information is lost. Only the fact that a button was pressed on your remote control unit is detected.

More about this Infrared Toggle Switch, download the manual

"Night Rider" 16 Stage Bi-Directional LED Sequencer circuit

This bi-directional LED sequencer circuit uses IC CD4516 and IC 74HCT138 as counter and decoder.

Circuit explanation:
The bi-directional sequencer uses a 4 bit binary up/down counter (CD4516) and two "1 of 8 line decoders" (74HC138 or 74HCT138) to generate the popular "Night Rider" display. A Schmitt Trigger oscillator provides the clock signal for the counter and the rate can be adjusted with the 500K pot. Two additional Schmitt Trigger inverters are used as a SET/RESET latch to control the counting direction (up or down). Be sure to use the 74HC14 and not the 74HCT14, the 74HCT14 may not work due to the low TTL input trigger level. When the highest count is reached (1111) the low output at pin 7 sets the latch so that the UP/DOWN input to the counter goes low and causes the counter to begin decrementing. When the lowest count is reached (0000) the latch is reset (high) so that the counter will begin incrementing on the next rising clock edge. The three lowest counter bits (Q0, Q1, Q2) are connected to both decoders in parallel and the highest bit Q3 is used to select the appropriate decoder.

source: http://www.qsl.net/yo5ofh/hobby%20circuits/led_circuits.htm

18W amplifier circuit based on IC HA13118

Here the 18W audio amplifier circuit which powered by IC HA13118 as the main component.The type of this amplifier is bridge amplifier since the output line does not grounded.

The supply voltage required for this circuit is 8 – 18V DC, at least 1 to 2 Amps. Maximum output power will only be obtained with a power supply of 18V at greater than 2 A, using a 4 ohm speaker. The power supply should be well filtered to reduce mains hum, a regulated supply will reduce noise even further. Extra filtering is unnecessary if operating from a battery supply.

View more explanation about this 18W audio amplifier circuit HERE.

16W Audio Amplifier with LM383 schematic diagram

Here the 16 watt power audio amplifier circuit powered by dual IC LM383. The single LM383 will amplify the input about 7-8 watt, dual IC should be gain up to 16 watt. You can use wide voltage range 5V - 20V to supply the power IC.

Component list:

U1, U2____________ LM383 power IC
R1, R3____________ 220 Ohm resistor
R2, R4____________ 2.2 Ohm resistor
R5________________ 1 MegaOhm resistor
R6________________ 100k potentiometer
C1, C7____________ 10uf electrolytic capacitor
C2, C5____________ 470uf electrolytic capacitor
C3, C4, C6________ 0.2uf ceramic capacitor
SPKR1_____________ 4 to 8 ohm speaker (up to 8 inches diameter)

10 Watt Amplifier with TDA2009A Schematic Diagram

This is schematic diagram of 10 watt power audio amplifier using TDA2009A as the main component.

Component list:

R1, R3_________ 1K2 ohm
R2, R4_________ 18 ohm
R5, R6_________ 1 ohm
C1, C2_________ 3u3 50V mini
C3_____________ 22uF 16V
C5_____________ 100uF 35V
C6, C7_________ 220uF 10V
C10, C11_______ 2200uF 35V
C4, C8, C9_____ 100nF
IC_____________ TDA2009A
Heat sink

Download 10 Watt Amplifier with TDA2009A Schematic Diagram in PDF version HERE

Preamp + Tone Control Circuit

This is a preamp and tone control which combined in in one circuit.
P1 to control the volume level, P2 to control Bass level and P3 to control Treble level.

This is a mono channel circuit, build another equal circuit to make this circuit stereo.

Component:

R1__________220K
R2__________100K
R3__________2K7
R4,R5_______8K2
R6__________4K7
R7,R8,R13___2K2
R9__________2M2
R10,R11_____47K
R12_________33K
R14_________470R
R15_________10K
R16_________3K3

C1,C2,C9____470nF 63V Polyester Capacitors
C3,C4_______47nF 63V Polyester Capacitors
C5,C6_______6n8 63V Polyester Capacitors
C7__________10µF 63V Electrolytic Capacitor
C8,C10______22µF 25V Electrolytic Capacitors
C11_________470µF 25V Electrolytic Capacitor

Q1,Q3_______BC550C 45V 100mA Low noise High gain NPN Transistors
Q2__________2N3819 General-purpose N-Channel FET